Home

Dolls

One Inch Scale

Half Inch Scale

Quarter Corner

Clothing Accessories

Miscellaneous

Costuming and Accessories Kits

 Supplies ,Tools and Books

Show & Class Schedule

Links

Tutorials

     Art Gallery     (some non-mini items)

Ordering Information

Faux Smocking Nightgown Tutorial

BuiltWithNOF
bkeyesul209
fauxshirrednightgown

 Materials
Fine, even weave cotton fabric (cotton batiste, Egyptian cotton, or other light weight fabric)
Lightweight cotton gauze or voile in matching or contrasting color
2 mm and 4 mm silk ribbon
Narrow trim or braid for shoulders
Narrow (1/4” wide or less) edging lace for hem and sleeve edges.  
 
Tools and Supplies
Small  sharp scissors for fabric
Scissors for paper
Small sewing needle
Insect pins, fine beading needles or fine silk pins
Steam iron or hand held steamer
” dowel
White tacky-type or fabric glue
Freezer or Butcher’s paper (paper which is coated on one side with wax or plastic)
Waxed paper
Syringe type glue gun or small tipped squeeze bottle for glue(optional)
Unscented hair spray, spray starch, or fabric stiffenener (Stiffy or Stiffen Stuff)               Ruler
 

wnight01

 Cut a piece of fabric 7 ” wide x 3” long.  Be certain that your cuts run parallel to the grain of the fabric.  Check the grain by pulling a thread of the fabric from the short side right near the long edge.  If you pull the thread all the way out of the fabric the empty space will create a cutting line right along the grain. Seal all edges with a very fine line of glue, especially if you plan to sew the garment.

wnight03

Measure  1/8” from the long edge and pull out one single thread in the same manner that you found the grain above.  This time you will use the empty space as a guide for the fold of your hem.

wnight04

Use only the tiniest amount of glue.

wnight14

Fold the fabric into four even sections and mark the center and each quarter fold with a pin or by taking a small stitch with a needle and contrasting thread along the unhemmed edge

wnight16

Cut a piece of lace  15 inches long. Divide into four even sections and mark in the same manner that you did for the fabric.

wnight18

Find the heading thread at one cut end in the top of the lace and put a small dot of glue on the end so that when you pull the thread to gather the lace, it will not pull through. If your lace does not have a heading thread you will have to sew a tiny running stitch all the way across the top part of the lace to gather.

wnight19

Use a tweezers to grab the header thread on the end that has not been glued  and begin to gather the lace.

wnight20

Lay your fabric on your workspace and, starting with the edge of the lace that you sealed with glue, match the first quarter division on both the lace and the fabric, pin together and adjust the gathers evenly between the two points. Run a line of glue along that quarter of the bottom edge (you may also sew for this step). Glue or sew this section together, then match the pieces of the next section. This procedure helps to make the gathers more evenly spaced. Continue until the entire piece of lace is attached.

wnight08

Dab a bit of glue along the top inch or so of one raw edge of the fabric to seal the threads.  Allow the glue to dry completely.

wnight10

Using a needle or straight pin, at the opposite raw edge, carefully pull up one long horizontal thread, about 1/8” from the outside edge and ” below the finished top edge (just below the hem).  Pull up a second thread about 1/16” below the first thread. Pull up two more threads at the same interval in this manner.

wnight25

Check to be certain that the glue on the opposite sealed edge has dried completely.  Now grab all the loose threads that you have pulled up into one hand.  Holding the threads firmly, GENTLY and carefully gather the fabric on these threads.  Pull into even gathers.  If a thread does break, pull another right next to it to replace it.
 

wnight031

If you plan to display the finished garment in a setting, gather so that the fabric measures about 2 ” across the gathered area.
 

Nightgown  032

 If you are dressing a one inch scale miniature doll, gather the fabric enough to wrap around your doll over the bust and under her arms with a 1/4 inch overlap for a seam. (NOTE: This garment should only be made on a doll with full porcelain arms as the arm will show through the gauze sleeve).

Nightgown 036a

After you have gathered the fabric, seal each of the threads with a drop of glue to keep the gathers from coming out.

Nightgown037a

Make certain that the gathers are even.  Pin natural looking folds to your ironing board, steam and let dry. The best pins to use are insect pins or very fine dressmaker pins as they  will not leave noticeable holes in the fabric.  You can make the folds more permanent by spraying a small amount of unscented hair spray, or other stiffening product of your choice over the folds, and letting the fabric dry again.

Nightgown  057

 If you are dressing a doll, fold the nightgown around the doll and over the bust so that the seam is up the center back.  Glue or sew it closed.  If making the garment by itself, you should close the back seam at this time as well.

SLEEVE.PDF

Click on link for sleeve pattern

wnight041a

Trace the sleeve pattern on the unwaxed side of freezer paper. Cut out and turn the pattern over to trace a second sleeve.

wnighat043

Using a warm iron, lightly iron the freezer paper patterns onto a piece of cotton gauze.  Keep the iron fairly cool and don’t press hard with the iron.  You want the wax/plastic on the paper to gently adhere to the fabric; not to saturate it.

wnight046a

 Cut out the sleeves by cutting the fabric around the edge of the paper pattern.  The freezer paper will keep the gauze stiff. which will make it much easier to cut accurately.                                          Peel the cut sleeves from the paper. It will easily pull away. Seal all edges by running a fine line of glue all the way around. Allow to dry thoroughly.

wnight046

Glue a piece of lace along the bottom of each sleeve.

wnight049

Sew a row of running stitches along the top edge of each sleeve, leaving a tail of thread to pull later. Sew another row of running stitches at the top of the lace trim where it joins the sleeve fabric (going through both layers of fabric).  Leave a tail to gather.

wnight050

Fold each sleeve right sides together and close underarm seams by gluing or sewing. 

wnight052

Press the seams.

wnight054

Pull the threads at the top of the sleeve so that the armhole opening, when laid flat, measures one half inch.  Tie the threads to keep in place.  If you are dressing a doll, slip a sleeve on the doll’s arm and pull up gathers to fit at the shoulder.

wnight055

Insert a pencil or small dowel into the sleeve and draw up the gathers in the bottom of the sleeve to fit the pencil (or if dressing a doll. gather to fit the doll's arm size).

wnight060

Slipstitch or glue the underarm portion of the sleeve to the body of the nightgown. Attach as neatly as possible.

wnight62

Repeat above steps for the second sleeve.

wnight63

Cut two 1 ” pieces of braid or other trimming for the shoulders. Neatly seal the cut edges with glue to keep it from unravelling.

wnight-64

Starting at the first (top) gather on the bodice, glue or sew the trimming up along the raw edge of the sleeve.

wnight65

Continue over the top of the shoulder and down to the first gather on the back of the gown. Repeat for the second sleeve.

wnight66

Make  two tiny bows with 2mm silk ribbon.  Cut short, angled  tails and attach one bow over each of the the front raw edges of the shoulder trimming. Your nightgown is ready to hang on a hanger or display in a miniature setting.

Back